{"product_id":"keramine-nanodanga-automobilio-kebului-ceramic-armor-coat","title":"Ceramic Nanocoating for Car Body Ceramic Armor Coat","description":"\u003cb\u003e\"CERAMIC ARMOR COAT\"\u003c\/b\u003e is a ceramic, extremely durable paint protection against adverse environmental effects. Unique technology creates a strong protective layer, protecting your vehicle from acids, alkalis, salts, rain, dust, ultraviolet rays. Surfaces coated with \"CERAMIC ARMOR COAT\" also acquire strong hydrophobic properties, allowing the car's surface to be easier to maintain, wash, and clean. A car coated with this product will remain clean and shiny longer.\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eAREAS OF USE:\u003c\/b\u003e Cars, yachts, motorcycles and other vehicles (trains, airplanes, windsurfers, etc.), any painted and varnished surfaces (car headlights, etc.), plastic trim elements. This product is not suitable for coating chrome-plated, unpainted painted parts. Newly painted surfaces can be coated no earlier than 2 months after painting. The product is also suitable for coating all types of painted and lacquered plastic surfaces.\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eINSTRUCTIONS FOR USE (read the entire instructions before coating the surface):\u003c\/b\u003e\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003e1. Preparation for coating\u003c\/b\u003e\u003cbr\u003e\nBefore coating the car with this product, the surface must be properly prepared. Recommended preparation: thoroughly wash the car, remove stubborn dirt with a special body clay bar, polish the body with appropriate products, degrease the surface with a silicone-removing cleaner, wash again and dry the car until it is completely dry. Make sure that no water remains in the gaps or trim details that could get onto the surface during coating (for this, we recommend blowing out all the water from the car's trim details, etc., with a strong air stream). If water gets onto the coated surface during coating, we recommend re-polishing the wet area and coating it again with \"CERAMIC ARMOR COAT\".\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003e2. Surface coating\u003c\/b\u003e\u003cbr\u003e\nMake sure that the surface is not hot and not exposed to direct sunlight. The temperature during coating must be between +5 and +25 °C. Wear the rubber gloves included in the kit during coating. Before opening the bottle, gently shake its contents and open the cap. Moisten the applicator pad with the product in 4-5 different places: press the applicator pad against the neck of the bottle and briefly turn it upside down, as shown in the video instructions on our website. Using the moistened applicator pad, rub the desired area to be coated with horizontal and vertical movements – make sure that no uncoated areas remain. One applicator pad should cover about 1 m², which should take about 75 seconds. After coating the area with the applicator pad, immediately wipe the surface with one microfiber cloth, and then wipe again with a second microfiber cloth until the surface is completely dry and smooth. You can use both sides of the cloths. Attention: do not leave the surface unwiped, as the nano coating hardens by reacting with air, so it is necessary to dry off the excess product with a microfiber cloth. If the product is not wiped off with cloths and it hardens, visible circles and stains may remain. These can be removed with 2000-grit sandpaper or an abrasive product. If the temperature during coating is higher than +25°C, and the humidity in the air exceeds 50%, coat areas no larger than 50 x 50 cm and polish with a microfiber cloth at the same time.\u003cbr\u003e\n\u003cbr\u003e\nAfter coating the entire desired surface, it must be protected from contact with water, dirt, chemicals, and friction for 24 hours. The coating fully forms and hardens 48 hours after application. Microfiber cloths used for coating should not be reused for cleaning lacquered, glossy plastic surfaces. We recommend that you carefully review the video instructions below before coating the car to avoid possible mistakes.\u003cbr\u003e\n\u003cbr\u003e\n\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/8dC0mvYKQcg\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eProduct consumption:\u003c\/b\u003e\u003cbr\u003e\n• Small cars (A-B class) 25-30 ml\/car\u003cbr\u003e\n• Medium cars (C-D class) 30-35 ml\/car\u003cbr\u003e\n• Large cars (E, SUV class) 35-40 ml\/car\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eProduct technical specification:\u003c\/b\u003e\u003cbr\u003e\n• Product quantity: 40 ml\u003cbr\u003e\n• Area of use: Cars, motorcycles, yachts\u003cbr\u003e\n• Effectiveness:\u003cbr\u003e\n  - 12 months \/ 50 washes under harsh conditions (from -40 °C to +40 °C; pH \u003e 12);\u003cbr\u003e\n  - 36 months \/ 150 washes under normal conditions (from -20 °C to +35 °C; pH \u003c 12);\u003cbr\u003e\n• Temperature resistance: up to 150 °C\u003cbr\u003e\n• Chemical resistance: 12\u003ePh\u003e1\u003cbr\u003e\n• Product consumption: 4-5 ml\/m²\u003cbr\u003e\n• Nano coating thickness: 700-1000 nm\u003cbr\u003e\n• Scratch resistance: 9H pencil test\u003cbr\u003e\n• Product validity: 1 year after opening\u003cbr\u003e\n• Storage conditions -3 °C to +30 °C, keep out of reach of children\u003cbr\u003e\n• Coating formation period:\u003cbr\u003e\n  - 6 hours the surface must be untouched and protected from dirt, precipitation;\u003cbr\u003e\n  - after 48 hours the coating is fully cured and resistant to the environment","brand":"Laverna","offers":[{"title":"Default Title","offer_id":53588449132885,"sku":"AP00NA3822","price":79.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1356\/2245\/files\/Keramine-nanodanga-automobilio-kebului-Ceramic-Armor-Coat.webp?v=1775510917","url":"https:\/\/www.autogarsas.lt\/en\/products\/keramine-nanodanga-automobilio-kebului-ceramic-armor-coat","provider":"AUTOGARSAS.LT","version":"1.0","type":"link"}