INFORMACIJA

JBL STAGE1 962M Gen2 – 6×9" (15.2 × 23 cm) 3-Way Coaxial Car Speakers

JBL STAGE1 962M Gen2 are larger 6×9" three-way coaxial car speakers designed for those looking to upgrade their car's audio system and achieve a richer, more dynamic, and clearer sound. This model is built as an upgrade for factory car speakers, while maintaining practical installation and the characteristic JBL sound.

The 962M Gen2 features 70 W RMS and up to 560 W peak power, 91 dB sensitivity, and a 45 Hz–20 kHz frequency response. The 6×9" format provides a larger cone area, allowing the speakers to deliver more solid bass and ensure higher sound pressure levels.

Key advantages of the JBL STAGE1 962M Gen2

• 6×9" (15.2 × 23 cm) size – larger cone area for a richer and more powerful sound.

• 3-way coaxial design – incorporates multiple elements for reproducing different frequency ranges in one speaker.

• 70 W RMS power – suitable for continuous, powerful music playback.

• 560 W peak power – allows the speakers to handle short-term high-power musical signals.

• 91 dB sensitivity – allows for high sound levels even when using a standard factory car audio system.

• 45 Hz–20 kHz frequency response – a wide spectrum of frequencies from low to high.

• 4 Ω impedance – the standard impedance for car audio systems.

• Plus One™ cone architecture – larger effective cone area, helping to produce more bass.

• PEI balanced dome tweeter – designed for clean and clear high frequencies.

• OEM-compatible construction – the speaker frame is designed for convenient installation in many factory locations.

• Included grilles – additional protection and a cleaner installation look.

Technical specifications

These characteristics correspond to the JBL Stage1 Gen2 962M specification.

6×9" format – more cone area

The JBL STAGE1 962M Gen2 uses a 6×9" (152 × 230 mm) oval format, which provides a larger cone area than typical car speakers with smaller diameters. The larger cone area helps deliver more solid bass and produce higher sound pressure.

This is particularly relevant when installing speakers in the rear deck or other locations where 6×9" format speakers are used from the factory.

3-way coaxial construction

The STAGE1 962M Gen2 is a three-way coaxial speaker. This means that several sound reproduction elements intended for different frequency ranges are integrated into one housing.

This allows for more balanced sound reproduction – from lower frequencies to the high details of vocals, instruments, and music.

Plus One™ cone architecture

JBL uses the patented Plus One™ cone architecture. Its principle is to increase the effective cone area compared to ordinary speakers of the same mounting size.

A larger cone area helps achieve higher sensitivity, more solid bass reproduction, and a more dynamic sound. This is one of the JBL engineering technologies used to maintain the signature JBL sound.

PEI balanced tweeter

The speakers use a PEI balanced dome tweeter, designed for clear high-frequency reproduction.

It helps to better highlight vocals, higher-frequency instruments, and fine musical details, while maintaining smooth sound. JBL also notes that this tweeter solution is designed to avoid overly harsh sound even at higher volumes.

Efficient sound reproduction

The 91 dB sensitivity means that the STAGE1 962M Gen2 can reach high sound levels without using extreme amplifier power. As a result, these speakers can be used with both a factory car audio system and an additional amplifier.

Using an additional amplifier allows for better utilization of the 70 W RMS power potential and provides more dynamics and control over the sound.

Wide 45 Hz–20 kHz frequency response

The frequency range reproduced by the 962M Gen2 reaches 45 Hz–20 kHz. This allows the speakers to convey not only mid and high frequencies but also a more solid portion of low frequencies.

However, if deep bass reproduction is desired, this model can be supplemented with a separate car subwoofer.

Convenient installation

The JBL Stage1 series speaker design is developed with OEM mounting locations in mind, so in most cases, complex modifications to the vehicle's structure can be avoided. The 962M Gen2 comes with the necessary basic installation hardware and protective grilles.

According to JBL installation documentation, the front dimensions of the 962M are approximately 240.3 × 168.7 mm, and the total mounting footprint is about 269.1 × 197.1 mm. Therefore, it is recommended to check the dimensions of the specific factory speaker location in your car before installation.

JBL Stage1 Gen2 – a practical audio system upgrade

The JBL STAGE1 962M Gen2 is the choice for those looking for larger 6×9" format car speakers with a three-way design, high sensitivity, and higher power headroom.

The 70 W RMS power, 560 W peak power, 91 dB sensitivity, 45 Hz–20 kHz frequency response, and 4 Ω impedance make for a practical combination for a daily car audio system upgrade. The Plus One™ cone and PEI tweeter help achieve a richer, more dynamic, and clearer sound characteristic of JBL.

What's in the box?

• 2× JBL STAGE1 962M Gen2 speakers

• 2× protective grilles

• 8× screws

• 8× speed clips

• 2× foam gaskets

• 1× quick start guide

JBL officially indicates that 2× gaskets are also included, so the installation kit is adapted for easier speaker setup.

Summary

JBL STAGE1 962M Gen2 – 6×9" three-way coaxial car speakers designed for upgrading a factory car audio system. 70 W RMS power, 560 W peak power, 91 dB sensitivity, and a 45 Hz–20 kHz frequency response allow for louder, more dynamic, and detailed sound. The larger 6×9" format, Plus One™ cone architecture, and PEI tweeter provide a good foundation for higher-quality car audio sound.