PT-HDBT-1010 PureTools - HDBaseT Extender with USB 2.0 and Audio Output, 4K (60Hz 4:4:4)

INFORMACIJA

4K 18Gbps HDMI HDBaseT Extender. The PT-HDBT-1010 HDMI over HDBaseT Spec 3 extender set transmits HDMI signals at full 4K@60 4:4:4 resolution up to 80 meters or 4K@60 4:2:0 resolution up to 100 meters. The set supports HDMI version 2.0 with a maximum bandwidth of 18 Gbps, including HDCP 2.2/1.4. Both the transmitter and receiver feature four USB-A "device" ports and one USB-B "host" port. USB signals, such as KVM, USB drives, or monitoring equipment, can be integrated at both ends and connected to a processing PC at the other. DIP switches on both devices allow for switching between "host" and "device" modes. Another DIP switch on the receiver sets the ARC mode to "HDMI," "S/PDIF," or "Pass-Through." The system allows for bidirectional transmission (or pass-through) of PoH/PoC and Ethernet. Both devices can be controlled individually via RS232. PureTools - high-quality electronic products for commercial applications. The PT-HDBT-1010 4K 18Gbps HDMI HDBaseT Spec 3 extender set consists of a transmitter (TX) and a receiver (RX) and transmits incoming HDMI signals via HDBaseT. Both devices are connected using a standard Cat. 5e / Cat. 6a cable up to 80 meters for 4K resolutions with a maximum 60 Hz 4:4:4 chroma subsampling or up to 100 meters for 4K resolutions with a maximum 60 Hz 4:2:0 chroma subsampling. The transmitter also features an HDMI loop output for local HDMI signal output at the TX location. Both devices feature one USB-B and four USB-A ports. The USB-A "device" ports allow connecting USB 2.0 devices and transmitting them to the other unit via HDBaseT, to which the processing "host" PC is subsequently connected via USB-B. This opens up numerous possibilities for USB signal distribution, such as connecting USB flash drives in a server room that can be easily accessed from a host PC at a workstation or presentation area. It also supports KVM devices, such as keyboards, mice, and webcams, for use with remote PCs. Hi-Speed USB 2.0 is supported, allowing the integration of both older and newer devices. Devices with USB 3.x or higher also transmit at the maximum USB 2.0 Hi-Speed data rate of 480 Mbps. Whether the transmitter or receiver operates in "host" or "device" mode can be easily configured using DIP switches on both units. Another distinct feature of the PT-HDBT-1010 is its versatile ARC compatibility, allowing connection to new and older audio equipment, such as AVRs. There are a total of three modes, which can also be easily switched using DIP switches. In "HDMI" mode, the ARC signal from a connected HDMI display is converted into a compatible audio signal at the receiver, then transmitted back to the transmitter via HDBaseT and output via HDMI and optical S/PDIF or Toslink ports. In this mode, CEC signal transmission is not supported. In "S/PDIF" mode, the ARC signal is routed from the receiver's S/PDIF input to the HDMI and optical S/PDIF or Toslink ports and output there. As the display device's CEC line is not used, it remains available for CEC pass-through applications. In "Pass" or pass-through mode, the actual ARC signal is transmitted, along with CEC, directly from the receiver's HDMI output port to the transmitter's HDMI and optical S/PDIF or Toslink ports, where it can be used for an ARC-supported audio device. The system supports bidirectional PoC or PoH power supply. This means that only one of the two devices needs to be powered using the included power supply, allowing the other unit to also be powered via the HDBaseT Cat. cable. This saves power supplies and reduces the number of cables at one of the two locations. Bidirectional 1G Ethernet signal pass-through allows for easy connection to Ethernet at a remote location without the need to lay an additional Cat. cable. Both devices feature an IR input and IR output, each with two 3.5 mm jack sockets. This means that a connected display can be controlled from the source device and vice versa. The system also supports CEC control data via HDMI, which is also transmitted via HDBaseT (except in ARC "HDMI" mode). Both the transmitter and receiver also feature a 3-pin Phoenix connector for control via RS232. Each device can be controlled individually and locally; RS232 control data is not transmitted from one device to the other via HDBaseT. The transmitter includes a 3.5mm stereo jack for audio de-embedding. This means that the HDMI input audio signal can be easily integrated into an existing audio system. The 12V power connector on both devices can be locked using a screw. Both units also feature multiple status LEDs, which indicate, among other things, the operating status, link, HDCP version, and loop status. PureTools - high-quality electronic products for commercial applications. The PureTools range includes high-quality audio-video electronic products, such as switchers, splitters, converters, and extenders for commercial AV installations and applications. The focus is on the transmission of digital signals such as HDMI, DisplayPort, DVI, and SDI. The combination of intelligent technology according to the latest standards, along with clever and practical innovations, makes the PureTools series products exceptional talents for professional installers and guarantees optimal project execution thanks to consistent performance.

• HDMI transmission over HDBaseT up to 100m (4K)
• Supports 18Gbps for resolutions up to 4K UltraHD 60Hz
• Bidirectional PoC and USB, RS232 and Ethernet pass-through
• Uncompressed transmission with HDBaseT 3.0, screw-lock power connector
• Analog audio de-embedding, ARC functions, 4 USB-A v2.0 KVM ports on TX / RX